This paintbrush is the best $1.25 I've spent on my grinder
-
- Posts: 637
- Joined: 17 years ago
Hello,
I'm sure most here already have a paintbrush to help with clearing the grinder out, but I just wanted to assure anyone who doesn't: head over to your local art supply shop and ask for their cheapest paintbrush with stiff(ish) bristles. The ones on mine are about right but a bit on the soft side. Now I will definitely be opening up the burrs more often (probably between coffees) to clear out the old stuff. On the Le'Lit a layer of coffee forms above the grind chamber sweepers and below the upper burr carrier, so it's certainly worth opening every so often.
Once again: get a cheap paintbrush if you don't have one! I might even get a second tiny one to get into the really small grooves in the burrs, but this one is good enough for now. I've attached a photo as well (note the screw in the removed upper burr marking the position it was in at my espresso setting).
Apologies for the poor quality photo... it's from a phone.
EDIT: I should note that I called 1st-Line asking for advice on how to remove the bottom burr, but Jim advised against that and suggested using grindz instead of removing any burrs at all. The advice makes sense, following the logic of "if it ain't broke, don't fix it."
I'm sure most here already have a paintbrush to help with clearing the grinder out, but I just wanted to assure anyone who doesn't: head over to your local art supply shop and ask for their cheapest paintbrush with stiff(ish) bristles. The ones on mine are about right but a bit on the soft side. Now I will definitely be opening up the burrs more often (probably between coffees) to clear out the old stuff. On the Le'Lit a layer of coffee forms above the grind chamber sweepers and below the upper burr carrier, so it's certainly worth opening every so often.
Once again: get a cheap paintbrush if you don't have one! I might even get a second tiny one to get into the really small grooves in the burrs, but this one is good enough for now. I've attached a photo as well (note the screw in the removed upper burr marking the position it was in at my espresso setting).
Apologies for the poor quality photo... it's from a phone.
EDIT: I should note that I called 1st-Line asking for advice on how to remove the bottom burr, but Jim advised against that and suggested using grindz instead of removing any burrs at all. The advice makes sense, following the logic of "if it ain't broke, don't fix it."
Dan Fainstein
LMWDP #203
PSA: Have you descaled lately?
LMWDP #203
PSA: Have you descaled lately?
- Psyd
- Posts: 2082
- Joined: 18 years ago
Remember that 'cheap' paintbrushes may shed broken bits of bristle, or entire bristles. I spent quite a bit of time fishing these bits out of my baskets when I used one to sweep out the doser on a regular basis. Speak to the sales folk and get them to suggest one that will *Not* shed parts. The extra five bucks may (YMMV) be cheap at twice the price.
Espresso Sniper
One Shot, One Kill
LMWDP #175
One Shot, One Kill
LMWDP #175
-
- Posts: 1
- Joined: 16 years ago
A good alternative to a conventional paint brush is what's called an acid brush....
It's got short, stiff (usually black) bristles and a short (usually rolled or pressed aluminum) handle.
They're usually in the paint section or sometimes in the plumbing section of your local hardware store.
Did I also mention....they're fairly cheap...?!
Even cheaper if you go to Harbor Freight, et al --- "cheaper by the dozen"....:>)
It's got short, stiff (usually black) bristles and a short (usually rolled or pressed aluminum) handle.
They're usually in the paint section or sometimes in the plumbing section of your local hardware store.
Did I also mention....they're fairly cheap...?!
Even cheaper if you go to Harbor Freight, et al --- "cheaper by the dozen"....:>)
-
- Posts: 637
- Joined: 17 years ago
How did you know? The brush has already lost quite a few bristles and most are shorter than they used to be. Turns out that in addition to eating coffee beans, burrs like to eat anything that touches them as they are not too dull.Psyd wrote:Remember that 'cheap' paintbrushes may shed broken bits of bristle, or entire bristles. I spent quite a bit of time fishing these bits out of my baskets when I used one to sweep out the doser on a regular basis. Speak to the sales folk and get them to suggest one that will *Not* shed parts. The extra five bucks may (YMMV) be cheap at twice the price.
Dan Fainstein
LMWDP #203
PSA: Have you descaled lately?
LMWDP #203
PSA: Have you descaled lately?
- Psyd
- Posts: 2082
- Joined: 18 years ago
How did you know?
I thought I'd covered that...
I spent quite a bit of time fishing these bits out of my baskets
![Wink :wink:](./../images/smilies/icon_wink.gif)
Espresso Sniper
One Shot, One Kill
LMWDP #175
One Shot, One Kill
LMWDP #175
- HB
- Admin
- Posts: 22029
- Joined: 19 years ago
-
- Posts: 637
- Joined: 17 years ago
Unfortunately internet doesn't convey my sarcastic tone. I'll check on getting an acid brush when this one runs out (in about one or two more cleanings...).Psyd wrote:I thought I'd covered that...
Thanks for the tip!
Dan Fainstein
LMWDP #203
PSA: Have you descaled lately?
LMWDP #203
PSA: Have you descaled lately?
-
- Posts: 2
- Joined: 16 years ago
I use a "dust buster hand vacuum cleaner it works great to get out all the old grinds and pick up any loose grind laying about the machine! The cordless ones i am not sure about the one i have is corded and has lots of pick up power and makes clean up a snap use my hand to form around the spout so has a good seal
Salvatore the only way to go for Quality made in the USA
-
- Posts: 31
- Joined: 16 years ago
HB wrote:That's what I use to sweep the chute. Here's a photo:
<image>
One brush is good for months before it gets frizzy.
Yeah that's the type of brush I use. I found them in the plumbing section at my local Lowe's home improvement store. They're typically used for applying flux for solder in the plumbing trade. Later!
-
- Posts: 637
- Joined: 17 years ago
Thanks for the tip. I'll check the hardware store instead of the art supply store.spro745 wrote:I found them in the plumbing section at my local Lowe's home improvement store. They're typically used for applying flux for solder in the plumbing trade. Later!
Dan Fainstein
LMWDP #203
PSA: Have you descaled lately?
LMWDP #203
PSA: Have you descaled lately?