When to replace burrs on Mazzer Mini

Grinders are one of the keys to exceptional espresso. Discuss them here.
DennisS
Posts: 35
Joined: 17 years ago

#1: Post by DennisS »

Hello all
i have a Mazzer mini, was new maybe 8 years ago
i grind about 1 pound per week over that entire time, it seems to be working fine but i assume the burrs
or other parts will not last forever

when is it due for maintenance (I don't want to do it myself) and what are the signs ?
tx
ds

User avatar
stefano65
Sponsor
Posts: 1405
Joined: 17 years ago

#2: Post by stefano65 »

Erratic changes in the grind
and having to go finer and finer
you can also remove them and feel the sharpness by going against the cut of the burr with your finger or nail
you can do a deep cleaning of the doser
Stefano Cremonesi
Stefano's Espresso Care
Repairs & sales from Oregon.

Advertisement
User avatar
sweaner
Posts: 3013
Joined: 16 years ago

#3: Post by sweaner »

It should certainly grind more than 400 pounds. Have you noticed any change in grind speed or change in it's output quality? Maybe it just needs a thorough cleaning?

If you have any questions, just replace the burrs and see. You can certainly do this yourself.
Scott
LMWDP #248

User avatar
HB
Admin
Posts: 21981
Joined: 19 years ago

#4: Post by HB »

According to the Mazzer owner's manual:
When using coffee blends of average hardness, it is advisable to replace the grinding blades approximately every:

600 kg for the Major model
400 kg for the Super Jolly model
300 kg for the Mini model. (approx. 660 pounds)
One pound a week for 8 years is more than 400 pounds. Unless the burrs feel sharp as Stefano suggests, I'd replace them.
Dan Kehn

User avatar
Randy G.
Posts: 5340
Joined: 17 years ago

#5: Post by Randy G. »

In the 6 or so years I had my Rocky I changed the burrs twice, about every two to three years or so. I estimate that about 75 pounds or so went through each set, but I never kept track. It could have been less... or more. I have never read what the actual rating on those burrs is, but based on my experience it is probalby no more than about 75 pounds, tops. With each time I changed the burrs the performance of the grinder was noticeably improved with each change. Why? For one set, some of the coffee I ground was Yemen, and the Yemen concrete drying pads are (were) disintegrating so bits of concrete did get ground at times. For more of that same coffee I would gladly sacrifice another set of burrs. It could also be a factor of the qualtiy of the burrs and the hardness of the alloy used or its heat treating (all sets were genuine Rancilio burrs). I don't know.

The bottom line is that your burrs are at a point that you have little to lose by changing them. Worst case is that you see no difference, and just keep the old ones as the spares. best case is that you have a new grinder which you won't have to worry about for another 6 years or so.
EspressoMyEspresso.com - 2000-2023 - a good run, its time is done

DennisS (original poster)
Posts: 35
Joined: 17 years ago

#6: Post by DennisS (original poster) »

thanks everybody for the comments and help
it is nice hear an actual number like 660 lbs
i don't have a manual
how involved is it to change the burrs, do they come with instructions?
if it weren't for the weight i would rather send it somewhere
of course then there is the downtime too

i am getting some oblique angle thin squirting sprays out of the bottom of my bottomless portafilter, think that could be related ?
ds

User avatar
sweaner
Posts: 3013
Joined: 16 years ago

#7: Post by sweaner »

HB wrote:One pound a week for 8 years is more than 400 pounds. Unless the burrs feel sharp as Stefano suggests, I'd replace them.
Dan, OK, that would be 416 pounds.:roll: He has another 3 years to go.
Scott
LMWDP #248

Advertisement
User avatar
HB
Admin
Posts: 21981
Joined: 19 years ago

#8: Post by HB »

I replace burrs at the halfway point, so by my standards, he's two years late.
Dan Kehn

CUBANERO
Posts: 48
Joined: 15 years ago

#9: Post by CUBANERO »

If you think that the grinding is good dont bother . If you are afraid of no grinder for a time just order burrs and let them sit until your grinding is not good. Even though a replacement after 8 years is not a bad choice,maybe your standards lowered parallel with burr deterioration.

User avatar
another_jim
Team HB
Posts: 13871
Joined: 19 years ago

#10: Post by another_jim »

Most pros I've spoken to suggest changing burrs when they reach half their rated life. It's a complete pain in the butt to blind compare old and new burrs, so I don't have any hard data to support this.
Jim Schulman

Post Reply