Mazzer Mini short hopper on Mazzer Major?

Grinders are one of the keys to exceptional espresso. Discuss them here.
McCann
Posts: 17
Joined: 16 years ago

#1: Post by McCann »

This should be an easy question for a Mazzer Major owner: Does the Mazzer Mini "extra short" bean hopper fit on the Mazzer Major? I have just ordered a Major for Chris' Coffee Service where I was told "absolutely not." However, somebody at http://www.espressoparts.com tells me that the short hopper they sell does fit the Major. Who is correct?

Any general suggestions for how to make the Major fit better into the average home (or in my case, small apartment) setting?

Thanks,
Mark

User avatar
HB
Admin
Posts: 21982
Joined: 19 years ago

#2: Post by HB »

The Major has an "interlock" collar like the Kony and Robur. The back of the collar has a tab that enters a slot; if the tab isn't slotted, the motor doesn't run. If you've seen the burrs on the larger Mazzers, you appreciate why. Anyway, the Major/Kony/Robur throat is slightly larger than the Mini or Super Jolly. I'm not aware of a shorter OEM hopper that fits it.
Dan Kehn

caeffe
Posts: 461
Joined: 16 years ago

#3: Post by caeffe »

I also have a newer Mazzer Major which has the collar interlock. Right now, I use it w/o the hopper (which BTW, was a Major PITA to remove from the collar). Keep in mind, I think the older ones don't have this interlock feature.

I have the same question will the Mini hopper (short or regular) fit the Major's interlock collar?
- so I can answer for sure, what is the OD of the mini-hopper that goes into the throat?
When I get home tonight, I'll measure the ID of the collar (or the OD of the hopper).

BTW, I'm able to get ~ 42 g (3 shots) into the throat with collar and the hopper slide 'closed'. The volume above the hopper slide is ~ 28 g (2 shots worth).

User avatar
cannonfodder
Team HB
Posts: 10497
Joined: 19 years ago

#4: Post by cannonfodder »

The interlock assembly is held on with two screws. Simply unscrew them, lift the plate (the switch is attached to the outer plate) up off the body. There is a small contact switch in there. You can put a chunk of something in there to hold the switch down, tape it down, or remove it and hotwire the two wires together to bypass the interlock. Usual disclaimers apply, not responsible for fire, electrocution, burnt up grinder, dismembered fingers, etc...

I am sure it will void your warranty.
Dave Stephens

caeffe
Posts: 461
Joined: 16 years ago

#5: Post by caeffe »

I am actually OK with having the collar/interlock. Also, as mentioned by Dan:
If you've seen the burrs on the larger Mazzers, you appreciate why.
I've seen the results of inserting my grinder brush too early in the grinder chute and shudder to think if anything other than coffee beans ends up in the grinder throat.

I use the interlock collar currently as a 'hopper' as I mentioned in my post above. It would be nice though to be able to have a larger column of beans on top so I can ensure that I have a consistent grind as mentioned in one of the threads here. I can definitely hear the beans popping against the hopper slide. I can always go with the PVC pipe route but I'm still interested as the OP is in whether the Mini hopper can fit in the interlock collar.

User avatar
Psyd
Posts: 2082
Joined: 18 years ago

#6: Post by Psyd »

caeffe wrote: I'm still interested as the OP is in whether the Mini hopper can fit in the interlock collar.
I have two older Majors, and neither have the interlock collar. With those, the mini hoppers fit nicely, TYVM! As far as the newer Majors go, I can't assist.
Espresso Sniper
One Shot, One Kill

LMWDP #175

caeffe
Posts: 461
Joined: 16 years ago

#7: Post by caeffe »

A couple of measurements of my Mazzer Major:

Interlock Collar ID to hopper: 65/66 mm
ID of grinder throat (interface with Interlock Collar): 60 mm

So, in order for the Mini hopper to fit in the Interlock Collar it needs to be <65mm
If the Mini hopper has an OD of <60mm then it can fit in the grinder throat w/o the interlock collar but one has to bypass the switch similar to what was done in the Titan Grinder project for the Kony/Robur (with a credit card).

k7qz
Posts: 236
Joined: 19 years ago

#8: Post by k7qz »

Here is what I did:

I removed the tall stock hopper from my Major but left the black collar and tab in place. I ordered a short Mini hopper and dropped it in the Major's collar. As has been noted, the diameter of the short hopper throat is smaller than the Major's collar opening. It works but rattles around and makes an annoying buzzing when the grinder runs. Also if you're not careful, you can knock a full hopper out of the collar, with resultant spilled beans decorating your kitchen floor. Don't ask... :oops:

So, I went down to my local plumbing supply house and bought a 2 1/2" black rubber couple (with end hubs). The one that I bought had hose clamps on each end held in place by the couple's ridged rubber collars (hubs). It set me back $2 or $3 as I recall.

I then removed the hose clamps and cut the ridged hub off of one end and slid the couple inside the Majors plastic collar. (sorry I still haven't replaced my "borrowed" digital camera yet but think T-shaped rubber bushing at this point) It was a bit of a snug fit to slide the couple in to the black collar but with a little patience it can be done. (it was easier when I placed the rubber couple flat on my counter and then wiggle-tapped the collar on to it from above) The hub of the rubber couple seats against the top opening of the plastic collar and gives it a "factory finished" look. After that, wiggle-tap the short hopper throat into the rubber couple (which acts as a bushing to take up the free space in the collar) and viola you're done!

Easy solution!

Oh, I was lazy and simply snapped off the hopper lock tabs to remove the tall hopper from the black collar. If you work carefully you can get the stock hopper off without having to break the tabs.

User avatar
cannonfodder
Team HB
Posts: 10497
Joined: 19 years ago

#9: Post by cannonfodder »

You could also wrap the mini hopper base with a band of electrical tape. Enough passes and you will create your own spacer to hold everything tight.
Dave Stephens

McCann (original poster)
Posts: 17
Joined: 16 years ago

#10: Post by McCann (original poster) »

Thanks for all the info. My new Major arrives this Thursday. The info above should give me a good starting point. Any chance somebody could post some pictures of what they've done?

- Mark

Aside: I just pulled some (to me) excellent doubles with my Zassenhaus grinder this morning. I'm really impressed at how consistent I can be from shot to shot with this little grinder. Still, I'm looking forward to stepping up the volume with my new Major. I've never used an electric grinder before, so it will be interesting to see what the difference is.

Post Reply