Search found 11234 matches
- Yesterday, 10:28 pm
- Forum: Coffee Roasting
- Replies: 1
- Views: 28
Drum roast profile on a fluid bed
It does. I run very similar bean temp profiles on my Quest drum and P1 air roaster. For the drum, I keep my environmental temp at roughtly 500F throughout. On the P1, I ramp up the inlet air temperature from 300F to 475F in the first seven minutes, and keep it steady for the last three. The final
- Yesterday, 4:57 pm
- Forum: Repairs, Restorations & Mods
- Replies: 5
- Views: 90
Afdichten (Sealing) boiler
I think your cut and paste fell into a time warp, and got tranlated in 1999
- Yesterday, 3:22 pm
- Forum: Repairs, Restorations & Mods
- Replies: 5
- Views: 90
Afdichten (Sealing) boiler
Here is a better translation:
- April 20th, 2024, 5:23 pm
- Forum: Grinders
- Replies: 454
- Views: 47149
Option-O Lagom 01 Discussion
I did molykote the timing belt, as suggested. It's been a quieter (more than a little bit, but not dramatic) when the motor speeds up for the purge; and it stayed that way for the past few weeks. Don't know if it's permanent, or if the lube will need to be repeated
- April 20th, 2024, 9:23 am
- Forum: Blog
- Replies: 56
- Views: 3699
Mazzer Philos Comments
I would like to comment on alignment before this thread goes off the rails. Per our own Jake-G, who rebuilds grinders and can do extensive testing, as well as high end grinder builders like Titus, simple tests at the zero point, like using a marker test or the gap betwen chirp and lock are not good ...
- April 19th, 2024, 11:31 pm
- Forum: Blog
- Replies: 56
- Views: 3699
Mazzer Philos Comments
The video in the last entry shows how the grind adjustment works. There is a lock at the zero marking (as well as the 145 marking), so it is impossible to make more than one turn on the adjustment wheel. I removed the collar to check for the chirp, and it was approximately at -3. After I changed
- April 18th, 2024, 2:33 pm
- Forum: Blog
- Replies: 56
- Views: 3699
Mazzer Philos Comments
I don't have any. I'm not even sure they would fit in a standard 64mm mount
- April 18th, 2024, 2:31 pm
- Forum: Blog
- Replies: 56
- Views: 3699
Mazzer Philos Comments
II haven't compared the Philos to the P64 or Zerno, since I have neither. This is a definite and huge missng piece in the review. It will be remedied when Dan and I send our review grinders to the next round of reviewers
- April 18th, 2024, 2:27 pm
- Forum: Blog
- Replies: 56
- Views: 3699
Mazzer Philos Comments
As I said in the review; I was able to pick them out in blind tests versus the Fuji 220, and preferred them (sweeter, about hte same clarity). The difference was slight; but hte Fujo is a major league brew grinder that has been used by several world brew champions. However, you can count me as an ex...
- April 18th, 2024, 3:26 am
- Forum: Tips and Techniques
- Replies: 11
- Views: 211
7g VST/LM Single Shot Basket Tips
Hope you're enjoying yourself. I go with 15 grams (2:1 ratio) out unless the roast is very light. I'm less worried about shot time than making sure the stream is really transparent by the time I get to 15 grams -- I want maximal extraction