Recent posts - Page 2
- Yesterday, 11:00 pm
- Forum: Buying Advice
- Replies: 30
- Views: 1361
Is Heat Exchanger Temperature Stability Really That Bad?
I'm not sure I follow your question. The Gagguino project is an open-source PID controller with oodles of extras, using the Arduino framework. Feed-forward control of the heating element, pressure control via phase modulation of the vibe pump, fancy displays and controls, etc... also, Gaggia classics or coffees or whatevers don't have pressurestats. They have thermostats with
- Yesterday, 10:58 pm
- Forum: Repairs, Restorations & Mods
- Replies: 5
- Views: 61
Casadio Undici A1 pump not turning on
I sent you PM you can give me a call to help you trouble shoot more sometime if you like. I am not sure have versed you are with electric and multimeter usage, but someone who is could see if you have power to the pump when a brew button is selected. Be careful you check the
- Yesterday, 10:50 pm
- Forum: Repairs, Restorations & Mods
- Replies: 1
- Views: 60
Wiring Diagram Desired For Espresso Marzocco Linea 2 EE Circa 1999
Jim, I have some, send me a PM and I can email one to you. Eric
- Yesterday, 10:41 pm
- Forum: Repairs, Restorations & Mods
- Replies: 7
- Views: 105
Short circuit La Marzocco Linea Classic AV
Also insure the power you are using is correct as far as 220 and if using a ground and neutral. I had someone hook up a 220 machine one time to 440 that will make smoke. Best wishes, take pictures when you find something
- Yesterday, 10:41 pm
- Forum: Espresso Machines
- Replies: 3
- Views: 48
La Marzocco GS3 Pre-Heater Element Question
You've got it right. The preheat element is a heat exchanger tube. It's worth ordering an additional gasket and soaking the element in citric acid if it has a thick layer of scale on the steam side (or inside), but generally there will be no benefit to replacing it if it isn't somehow broken. I can check tomorrow to verify
- Yesterday, 10:37 pm
- Forum: Repairs, Restorations & Mods
- Replies: 7
- Views: 105
Short circuit La Marzocco Linea Classic AV
You should always have water connected prior to turning a machine on. Was the power connected properly? There is installation and user manuals available on the La marzocco website. You can go on La marzocco USA site. That being said did you unplug it and investigate where the smoke came from? If smoke actually came out I doubt
- Yesterday, 10:21 pm
- Forum: Espresso Machines
- Replies: 277
- Views: 21009
La Marzocco Linea Mini R
Hi Joola, Where did you get the coffee bar?
- Yesterday, 10:09 pm
- Forum: Buying Advice
- Replies: 5
- Views: 105
Hopper fed grinder
I'd second the Eureka Specialita. It has a ton of great stuff going for it. You can also get it in the grind by weight model, Libra
- Yesterday, 10:08 pm
- Forum: Grinders
- Replies: 19
- Views: 864
Shot inconsistencies with SSP Cast LS
I have the exact same setup and am trying to learn here. What does "run out" mean and how is it measured? And how do you test the bottom burr alignment (and re-align it as well?) using tape?
- Yesterday, 9:46 pm
- Forum: Espresso Machines
- Replies: 3
- Views: 48
La Marzocco GS3 Pre-Heater Element Question
actually I am very curious if the GS3 can use a 2000w heating element ? I know that the GS3 steam boiler can be heated up to 2 bars, was wondering what is the lowest pressure it stays if you purge the steam for approx 50 seconds ? I am always wondering if 1200w heating element