Recent posts
- less than a minute ago
- Forum: Lever Espresso Machines
- Replies: 16
- Views: 409
Olympia Cremina lever questions after group gasket replacement
It seems like it's something simple to be rectified like the grind setting and after that it should work. The fun part is perfecting the quality of espresso. Good luck
- 3 minutes ago
- Forum: Espresso Machines
- Replies: 3
- Views: 61
Breville Dual Boiler gurgling, Brand New machines x 2
I get something similar to this on my Profitec 300 after emptying the boilers. It goes away after a few shots. Is this affecting the ability to pull a shot or steam?
- 29 minutes ago
- Forum: Espresso Machines
- Replies: 3
- Views: 61
Breville Dual Boiler gurgling, Brand New machines x 2
It's hard to tell from my end. Is it fully heated? (How long has it been on?) Has it had a chance to totally fill with water? Sometimes machines are a little weird when they are brand new and just filling reservoirs, boilers, lines, etc. How much water in total have you run through the machine?
- 32 minutes ago
- Forum: Espresso Machines
- Replies: 6
- Views: 196
Espresso shot - coffee appears immediately - problem?
"18 g in, 36 g out, in 25 seconds" or whatever is merely a benchmark that becomes familiar with time. Experience will get you to the point where you sense that, for example, for the amount of bitterness you taste, two notches finer on the grinder will get you closer to a good shot. Grind, dose, and ratio will
- 42 minutes ago
- Forum: Espresso Machines
- Replies: 8
- Views: 184
Inconsistent extractions on Breville Bambino Plus
In addition to my post of the 15th, with the exception of a handful of traditional Italian roasters, "best by" is best avoided. Virtually all supermarket brands are crap. A good roaster is better than a mediocre local one. What does your local cafe that has espresso you enjoy use? I'd look for a medium-dark roast, not oily, that suggests
- 42 minutes ago
- Forum: Coffee Brewing
- Replies: 23
- Views: 749
Mobile or hotel room brewing?
You might think that but you're wrong. And while reaching for the improbable don't forget to include infectious prions in the mix. It's not completely impossible that someone with Creutzfeldt-Jakob disease washed their underpants in your hotel kettle. Of course it can happen. It's naive to think that strict regulations translate into strict adherence. There are certainly food workers
- 1 hour ago
- Forum: Blog
- Replies: 41
- Views: 2407
Mazzer Philos Comments
Why would a Mazzer be inferior as they have way more experience than Zerno and own tons of equipment for building gear that Zerno will never own. And you do know that the marker test is by far a good test for proper alignment as there's much more to alignment. I do think you're underestimating Mazzer. And as Jim
- 1 hour ago
- Forum: Espresso Machines
- Replies: 259
- Views: 20200
La Marzocco releases Brew by Weight for Linea Mini
I get something kind of like that with my DIY version and standard Acaia scale, but I figured it was a glitch in the Bluetooth library or scale library software and not the scale itself. It will always "connect" immediately, but occasionally it will connect and won't send data, so I don't get weight numbers. I then have to
- 1 hour ago
- Forum: Blog
- Replies: 41
- Views: 2407
Mazzer Philos Comments
There's a high probability those i200d won't fit in an Ode. The other 64mm Mazzer (OEM) burrs normally don't AFAIK. Just to share my experience, I haven't noticed obvious differences between SSP MPv1 ("brew"/"unimodal v1") mounted in a Mazzer Mini E or Fellow Ode. Very minor if any, swapping them back and forth. With 50Hz outlets they should spin