Recent posts
- 9 minutes ago
- Forum: Repairs, Restorations & Mods
- Replies: 0
- Views: 0
Linea Mini steam issues
I've had a Linea Mini for about 5 years and haven't had any major issues with it. However, yesterday morning I noticed that the steam is not as dry as it used to be and it spits out more water than before. My wife also noticed that when the steam boiler is loader when heating up. Any ideas what
- 30 minutes ago
- Forum: Repairs, Restorations & Mods
- Replies: 0
- Views: 9
E61 overpressure during backflushing
I have a well maintained Izzo Duetto IV which is 2 years old and has a flow control kit. I backflush 5x back to back once a week and the same but with detergent once every 3-4 months. Everything works fine - no pressure problems during brewing, excess tray dripping etc. V. happy with machine. I
- 39 minutes ago
- Forum: Repairs, Restorations & Mods
- Replies: 8
- Views: 223
Breville Dual Boiler - Hissing + Maintenance
Order those o-rings and set a PM schedule to replace them at least every two years. I replace mine on an annual basis
- 51 minutes ago
- Forum: Espresso Machines
- Replies: 0
- Views: 4
Breville Barista Express - Machine stopped working after water leak
I'll appreciate your help! I just replaced today the stock OPV with the Vibiemme one according to this guide - {link} I messed something up and when I first connected the 4mm tube, I didn't pull out the metal thing, so it sprayed water when I first turned it on. I fixed it and when I connected the
- 1 hour ago
- Forum: Buying Advice
- Replies: 4
- Views: 138
Have owned a La Pavoni Professional for over a year... need decent grinder.
"[FS] Goat Story Arco Combo Electric & Hand Grinder" Here, in the Buy/Sell forum is the best of both worlds. A very capable and consistent hand grinder with an electric dock. Just a bit over your budget, but not by much. I've been using the ARCO hand grinder in my travel kit(I travel a lot!) since it came
- 1 hour ago
- Forum: Espresso Machines
- Replies: 444
- Views: 61155
The Meticulous Home Espresso Machine (Kickstarter)
So far I have decided to stay with my humble, simple and noisy bezzera unica! I have got my integrated PID driven boiler and a flow profile extraction. I doubt if the pressure accuracy of the the meticulous will make a notable difference in my so far flat extractions that I use lately Plus I can have an easy
- 2 hours ago
- Forum: Lever Espresso Machines
- Replies: 20
- Views: 958
Yellow water when emptying La Pavoni Europiccola boiler
Hi Bobsy Do you have an update on the discoloured water cause/source? Cheers, Paolo
- 2 hours ago
- Forum: Repairs, Restorations & Mods
- Replies: 3
- Views: 175
SAB 2gr Jolly Auto touchpad issue
Try to verify if all the flowmeters wires are connected properly. In this diagram SLIV is the boiler water level probe, which you have, probably you don't have the SLIVmin, ( minimum level probe) but for you is enough to check how SLIV and the flowmeters are connected. By the way the jumper i previously mentioned is in the right
- 3 hours ago
- Forum: Lever Espresso Machines
- Replies: 10
- Views: 298
(Ab)using the Europiccola to pull coffee instead of espresso
I tried that once on vacation, but wasn't much better than storing outside the fridge (for espresso at least). It was medium roast; I suppose it would be better with light roast, but that is aging slower at room temperature as well. And it was summer, so a lot of condensation I suppose
- 3 hours ago
- Forum: Repairs, Restorations & Mods
- Replies: 3
- Views: 175
SAB 2gr Jolly Auto touchpad issue
Giampero, thanks for the reply. Do you have any more information about this? I'm not sure what I'm looking at when I'm trying to figure out an issue that involves a board. Here is an image of the board where the flowmeters and level probe are wired into the board. Does this help answer anything? {image}