Vacuum breaker - serviceable?

Need help with equipment usage or want to share your latest discovery?
User avatar
Ozark_61
Posts: 244
Joined: 19 years ago

#1: Post by Ozark_61 »

My vacuum breaker on my ecm giotto is leaking / hissing. Anyone know if it's something that can be simply descaled or re-gasketed?

Cheers
Geoff
LMWDP #570

User avatar
erics
Supporter ★
Posts: 6302
Joined: 19 years ago

#2: Post by erics »

Geoff -

See the 5th post down in this thread:

Resolved: Anita boiler and steam troubles

Vacuum breaker valves are pretty inexpensive from a variety of sources so it may pay to order a new one especially if you have some other goodies in mind. Send me a pic of yours at erics@erols.com and I'll see what I have.
Skål,

Eric S.
http://users.rcn.com/erics/
E-mail: erics at rcn dot com

Advertisement
User avatar
shadowfax
Posts: 3545
Joined: 19 years ago

#3: Post by shadowfax »

I took mine apart a few weeks ago, and when I was removing the rubber o-ring to clean the metal parts, I broke the o-ring in half. A trip to home depot and $4 later, I had a little box full of o-rings that were a pretty good match. It took awhile to find them in that awfully laid-out store, but it worked. Later in the week I ordered a replacement, which I have on hand now in case anything goes wrong, but I found that disassembling, cleaning, and replacing that o-ring did the trick for me.
Nicholas Lundgaard

User avatar
mhoy
Posts: 1138
Joined: 16 years ago

#4: Post by mhoy »

Absolutely. However they are also inexpensive to replace. :D Clean it out with citric acid and get a heat resistant O ring. My Elektra also had a soft copper washer between the copper tank and the vacuum breaker. I got a spare O-ring from a guy I had helped out in Montreal. Pretty decent folks hang out around here.

If you do replace it, when was the last time you replaced your group head gasket? Yearly will prevent it from turning from an easy job to a frustratingly hard job.

Mark

User avatar
cafeIKE
Posts: 4704
Joined: 18 years ago

#5: Post by cafeIKE »

Kind of like sparkplugs: Once you've gone to trouble to get it out, replaced the seal, is it worth the trouble to put back?

User avatar
Ozark_61 (original poster)
Posts: 244
Joined: 19 years ago

#6: Post by Ozark_61 (original poster) »

I buy several gh gaskets for the e61 head at a time... but that's nothing to do with the vacuum breaker though... Does Home Cheapo carry the heat resistant o rings? If it's just that, I'll replace the o-ring and descale it.
LMWDP #570

User avatar
trzynkaa
Posts: 42
Joined: 15 years ago

#7: Post by trzynkaa »

High temperature o-rings....

Sorry, I do not expect home depot (or most hardware stores) to stock viton or silicon o'rings. Buna is the standard material and not really suited for a vacuum breaker on a boiler. However there are o-ring distributors on the net that list viton o-rings. Google "viton o ring".
For example: http://www.applerubber.com lists viton and other high temperature o-rings.
Andrew

Advertisement
User avatar
Ozark_61 (original poster)
Posts: 244
Joined: 19 years ago

#8: Post by Ozark_61 (original poster) »

Any idea of the size needed?
LMWDP #570

User avatar
Ozark_61 (original poster)
Posts: 244
Joined: 19 years ago

#9: Post by Ozark_61 (original poster) »

Actually - does anyone know if this is it?

http://www.espressoparts.com/product/W1 ... _L190.html
LMWDP #570

User avatar
mhoy
Posts: 1138
Joined: 16 years ago

#10: Post by mhoy »

Take out your current one, head over to OSH (or equiv) and see what thread size the bottom of your current one is. Then you could be sure.

Mark.

Post Reply