Search found 85 matches
- September 18th, 2012, 8:25 am
- Forum: Grinders
- Replies: 99
- Views: 12467
Mazzer Robur E vs. Kony E
I noticed that when the LM cycles for maintaining heat (the faint little beep beep beep from the area of the PID) it lowers voltage enough to change the RPM of my Versalab slightly. I switched to Versalab to a different circuit in the kitchen and it no longer varies it's speed. If you are running of...
- September 18th, 2012, 6:59 am
- Forum: Grinders
- Replies: 1296
- Views: 166307
Owner experience with Pharos manual coffee grinder by Orphan Espresso
Good man! My wife was "Out Shopping" so could not get in on the fun The only MOD from here is to drill another set of holes so the Zero Bar can be stored on the grinder when not in use. I was thinking about using one of the OEM Pharos rubber pads on
- September 17th, 2012, 9:27 pm
- Forum: Grinders
- Replies: 9
- Views: 6984
Mazzer Doserless Static Problems
Excellent examples! The factory engineers knew what they were doing
- September 17th, 2012, 10:10 am
- Forum: Grinders
- Replies: 64
- Views: 19553
Ceado E37 owner experience
Whew! I was afraid that the paramedics would be needed I might eventually end up trying to buy another one(E37) in the future if I get a new flat burr grinder. By then I suppose that all the teething issues will be done. I sure like the size, weight ease of setup
- September 16th, 2012, 9:26 pm
- Forum: Grinders
- Replies: 349
- Views: 51805
Versalab M3 grinder owners
Yeah, it's not a lot. Changing the cone with the ability to be coated might do it. Keep us all Posted!
- September 16th, 2012, 9:01 pm
- Forum: Grinders
- Replies: 349
- Views: 51805
Versalab M3 grinder owners
Very nice lathe! I certainly wish I had that sitting in my shop, and a shop large enough for it!!!!!! Here is the plastic ring on the bottom of the cone that seems to collect (via static) particles. {image}
- September 16th, 2012, 7:05 pm
- Forum: Grinders
- Replies: 349
- Views: 51805
Versalab M3 grinder owners
I played around with some cocobolo for an anti-popcorn cap today. Nowhere as nice as the work that Dave S. does but it is sure better than the foam that I have been using. Next step is the aluminum model Terranova, how are you coming on the ceramic coating on the lower cone? Did
- September 16th, 2012, 2:28 pm
- Forum: Grinders
- Replies: 1296
- Views: 166307
Owner experience with Pharos manual coffee grinder by Orphan Espresso
Just finished the VooDooDaddy MOD today on #00520-V. Pretty simple to do and aligning the burrs worked out well using the Pharos YouTube #5 video AND with that philosophy in mind I did the Pharos alignment procedure. Then I aligned the lower VooDooDaddy bearing carrier bracket which got that bracket...
- September 16th, 2012, 8:39 am
- Forum: Grinders
- Replies: 44
- Views: 7892
Doserless conversion Wega rebranded Compak K10 WIP
I was considering a K10 and this certainly is a good practical Thread while considering! Thanks
- September 16th, 2012, 8:21 am
- Forum: Grinders
- Replies: 64
- Views: 19553
Ceado E37 owner experience
NO COFFEE FOR 3 DAYS Yikes, I would be looking for aspirin